Ask anyone how Giza Pyramids were constructed and most people will respond by talking about ramps. Most websites dealing with Giza Pyramids construction promote various ramp theories and many people, including mass news media are very persuasive. The single long ramp theory attributed to Pharaoh Khufu's Great Pyramid has been established as a worldwide consensus theory and has been so for around one hundred years.
Pharaoh Khufu had The Great Pyramid built for his own use and the logistics of construction were well understood by his father's Pyramid constructions where new building techniques were being established. Ramp theories present a glaring engineering logistical debacle because the construction time-frame for Great Pyramid construction is documented and is twenty years, so logically it is not possible to construct The Great Pyramid and construct a ramp upon which Pyramid blocks are being hauled one block following another consecutively. Additionally the ramp requires adjustments of elevation throughout its use and finally the ramp needs to be removed.
Some claim the long ramp theory is fact and some, with caution, use terms like "most likely" and "probably", but as you have just read all this talking up of ramps is in fact nonsense. The simple truth is, there was no ramp or ramps of any type, any design for raising Giza Pyramid blocks on the Pyramid itself, simply because a Giza Pyramid in progress of construction is built layer upon layer and each layer is decreasing in area and producing steps all around the four sides and height, all logically designed for the specific purpose of using step-walking pulleys operating over all four sides of a Pyramid simultaneously. The step walking pulleys used in Giza Pyramids construction are unlike any pulley known in our modern world and were re-discovered in 2006.
What follows has been known since 2006 via university research, however only Pravda in Moscow published the article titled "The Documented Ancient Construction Method of The Great Pyramid". Pravda placed the article on the London Global News Exchange in 2019 where it was ignored, or perhaps avoided.
Consider the movement of blocks in two ways ... Consecutively or Simultaneously and knowing the documented time-frame for the Great Pyramid is 20 years. Logistics of Engineering can only accommodate the SIMULTANEOUS movement of blocks which absolutely rules out consecutive and thus rules out ALL ramp and water shaft-canal theories.
The method used is known today as Rack & Pinion Mechanical Technology and the Egyptians developed its prototype at Giza. Those hundreds of limestone steps you observe for all Giza Pyramids are RACKS, over all four sides and height.
Inty Shedu was the carpenter in chief at Giza and fabricated LOBES made from short planks of Cedar which had been imported from Lebanon as we know via the "Palermo Stone". Evidence for the "four lobe pinion pulley" is the "Petrie rocker" excavated in 1895 by Edouard Neville and handed to Petrie in person for his London museum.
The Shedu four-lobe pinion-pulley is a machine of Class Two Lever Principle, Pivot-Load-Effort, same as a forward wheel, wheel-barrow, and has a mechanical advantage of 2.8 (MA=2.8) which means a 2500 kg Pyramid block can be raised with an input effort of 900 kg. Search haitheory
https://haitheory.com/Inty_Shedu.html
_________________________________________________________________________________________________________________________________________________________
The engineering logistics of CONSECUTIVE traffic of blocks raised within the documented twenty year time-frame rules out ALL ramp and water-shaft canal theories which all have "one block follows another' illogical approach. Blocks were moved SIMULTANEOUSLY over all those STEPS you see of all Giza Pyramids. Four-lobe pinion-pulleys were used on and over ALL available horizontal STEP surface area. Hoist one block per hour over an eight hour day. Forty pulleys, ten per side, raise 320 blocks.
Over a year, 365 days 116,800 blocks are raised. Over Twenty years 2,336,000 blocks have been raised. The method is known in our modern world as Rack and Pinion mechanical engineering. Those hundreds of limestone STEPS can be termed RACKS. The Pinions were fabricated from imported Lebanese Cedar timber under the supervision of Chief Carpenter Inty Shedu who was entombed on the Giza Plateau. Inty Shedu's four tomb statues are exhibited in the Cairo museum. The Shedu Four-Lobe Pinion-Pulley has an innate mechanical advantage of 2.8 (MA=2.8) which means a 2500kg Pyramid block is raised with an input effort of 900kg. Search haitheory website and haitheory at YouTube.
https://www.youtube.com/@haitheory
Pharaoh Khufu had The Great Pyramid built for his own use and the logistics of construction were well understood by his father's Pyramid constructions where new building techniques were being established. Ramp theories present a glaring engineering logistical debacle because the construction time-frame for Great Pyramid construction is documented and is twenty years, so logically it is not possible to construct The Great Pyramid and construct a ramp upon which Pyramid blocks are being hauled one block following another consecutively. Additionally the ramp requires adjustments of elevation throughout its use and finally the ramp needs to be removed.
Some claim the long ramp theory is fact and some, with caution, use terms like "most likely" and "probably", but as you have just read all this talking up of ramps is in fact nonsense. The simple truth is, there was no ramp or ramps of any type, any design for raising Giza Pyramid blocks on the Pyramid itself, simply because a Giza Pyramid in progress of construction is built layer upon layer and each layer is decreasing in area and producing steps all around the four sides and height, all logically designed for the specific purpose of using step-walking pulleys operating over all four sides of a Pyramid simultaneously. The step walking pulleys used in Giza Pyramids construction are unlike any pulley known in our modern world and were re-discovered in 2006.
What follows has been known since 2006 via university research, however only Pravda in Moscow published the article titled "The Documented Ancient Construction Method of The Great Pyramid". Pravda placed the article on the London Global News Exchange in 2019 where it was ignored, or perhaps avoided.
Consider the movement of blocks in two ways ... Consecutively or Simultaneously and knowing the documented time-frame for the Great Pyramid is 20 years. Logistics of Engineering can only accommodate the SIMULTANEOUS movement of blocks which absolutely rules out consecutive and thus rules out ALL ramp and water shaft-canal theories.
The method used is known today as Rack & Pinion Mechanical Technology and the Egyptians developed its prototype at Giza. Those hundreds of limestone steps you observe for all Giza Pyramids are RACKS, over all four sides and height.
Inty Shedu was the carpenter in chief at Giza and fabricated LOBES made from short planks of Cedar which had been imported from Lebanon as we know via the "Palermo Stone". Evidence for the "four lobe pinion pulley" is the "Petrie rocker" excavated in 1895 by Edouard Neville and handed to Petrie in person for his London museum.
The Shedu four-lobe pinion-pulley is a machine of Class Two Lever Principle, Pivot-Load-Effort, same as a forward wheel, wheel-barrow, and has a mechanical advantage of 2.8 (MA=2.8) which means a 2500 kg Pyramid block can be raised with an input effort of 900 kg. Search haitheory
https://haitheory.com/Inty_Shedu.html
_________________________________________________________________________________________________________________________________________________________
The engineering logistics of CONSECUTIVE traffic of blocks raised within the documented twenty year time-frame rules out ALL ramp and water-shaft canal theories which all have "one block follows another' illogical approach. Blocks were moved SIMULTANEOUSLY over all those STEPS you see of all Giza Pyramids. Four-lobe pinion-pulleys were used on and over ALL available horizontal STEP surface area. Hoist one block per hour over an eight hour day. Forty pulleys, ten per side, raise 320 blocks.
Over a year, 365 days 116,800 blocks are raised. Over Twenty years 2,336,000 blocks have been raised. The method is known in our modern world as Rack and Pinion mechanical engineering. Those hundreds of limestone STEPS can be termed RACKS. The Pinions were fabricated from imported Lebanese Cedar timber under the supervision of Chief Carpenter Inty Shedu who was entombed on the Giza Plateau. Inty Shedu's four tomb statues are exhibited in the Cairo museum. The Shedu Four-Lobe Pinion-Pulley has an innate mechanical advantage of 2.8 (MA=2.8) which means a 2500kg Pyramid block is raised with an input effort of 900kg. Search haitheory website and haitheory at YouTube.
https://www.youtube.com/@haitheory
Last edited: