What stops alternative current from going bang ?

I bought into the Agincourt myth of the V sign, it sounded plausible, English and rather cool.
Sadly there is very little evidence to support anything to that. I found this small piece on it.

Yes, I was once told this by a bloke in the office who was an archer, but I was a bit sceptical.

Jingoistic Brits often tediously go on and on about Agincourt, Crécy, Poitiers, etc., but the fact is England comprehensively lost the Hundred Years War, after causing great destruction and loss of life in France. At the start the medieval Kings of England owned the whole of Normandy and Aquitaine, - about half of modern France - but by the end they had just Calais (later to be lost by Mary I). Shakespeare is partly responsible for this skating over of the reality.

It was only through being married to a Frenchwoman that I came to fully appreciate this uncomfortable fact. :)
 
Yes, I was once told this by a bloke in the office who was an archer, but I was a bit sceptical.

Jingoistic Brits often tediously go on and on about Agincourt, Crécy, Poitiers, etc., but the fact is England comprehensively lost the Hundred Years War, after causing great destruction and loss of life in France. At the start the medieval Kings of England owned the whole of Normandy and Aquitaine, - about half of modern France - but by the end they had just Calais (later to be lost by Mary I). Shakespeare is partly responsible for this skating over of the reality.

It was only through being married to a Frenchwoman that I came to fully appreciate this uncomfortable fact. :)
Henry had a rather unheroic early death too. Still, we got a play out of it but I think I would risk a dose of 15thC French dysentery than sit through it.
 
Henry had a rather unheroic early death too. Still, we got a play out of it but I think I would risk a dose of 15thC French dysentery than sit through it.
Yes, those are not my favourite plays. I keep telling myself I should have another go at Hamlet, but those Henry plays are not on my bucket list.
 
And you need to make some minimal effort to research your new topics before you post them, Sunshine.

Very happy to learn you are not an electrician.
The there would be no need to a have a forum if people like me just googled everything . Where would the discussion be if people like me were know it alls ?
 
(Also a small note: resistors (post#5) do not have a "direction".

Some components, such as diodes, transistors, and some capacitors, do have a polarity and will need to be installed as per the design of a circuit. Which is half the point here. A circuit is designed to run on AC or DC as required. (Often a device will convert AC to DC and both may be used inside.) The daft OP here seems to think a circuit gets designed, built, and then the power input is some kind of surprise.)
Several posts later and I have still not gained any sort of answer . If people don't know themselves perhaps they should just not try to post like some of the flame baiters in this thread . You sound like you know some electronics . A simple light bulb , 1.5mm twin and earth , the earth is not attached to the bulb . There is a blue wire and a brown wire . The brown wire is live and the blue is neutral , if the electricity reversed direction , shouldn't the neutral also be a live wire ?
If the electricity reversed direction , how does the light bulb not go bang when there is the brown and blue wire pumping current into it ?
What in a main fuse board allows the electricity to be reversed ? How can a switch work , designed for a circuit , if there is a reverse ?
I think the blue wire goes back into the national grid , I think we are all being ripped off unless I get an answer proving me wrong .
 
The there would be no need to a have a forum if people like me just googled everything . Where would the discussion be if people like me were know it alls ?
Posters usually have tried reading a couple of books on the subject, a general readers here, a textbook there, some school perhaps?
 
Posters usually have tried reading a couple of books on the subject, a general readers here, a textbook there, some school perhaps?
My first ever job was selling domestic and commercial electrical components such as plugs sockets , wiring , swa , RCB's etc . I have never sold a component that could reverse electrical current direction . I am not a novice on components so would like to know how AC suppose to work when there is no apparent component for the process . I could go and read up more on this subject but no doubt it will be written in a confusing way so the average person can't understand it . Here I am looking for an explanation from the horses mouth as they say , surely all these posters so far , somebody can explain the process to me in simple terms to remove my concerns . The more people ignore this , the more I think my suspicions are correct .
 
[...] If the electricity reversed direction , how does the light bulb not go bang [...]

Why would the light bulb explode? It's the same fluctuating amount of current/voltage going through it no matter which part of the AC cycle. It's built to handle that.

Perhaps the issue here is that you need to clarify where your expectation of things "going bang" is ultimately coming from. For instance, asking why birds don't explode when it rains is not quite a comparable analogy but would still evoke similar puzzlement from people. "What the ___?"
_
 
Why would the light bulb explode? It's the same fluctuating amount of current/voltage going through it no matter which part of the AC cycle. It's built to handle that.

Perhaps the issue here is that you need to clarify where your expectation of things "going bang" is ultimately coming from. For instance, asking why birds don't explode when it rains is not quite a comparable analogy but would still evoke similar puzzlement from people. "What the ___?"
_
touch two live wires together and it will spark , even at low voltage . High voltage would create a bigger spark , a ''
bang''

Why would you and others avoid answering the initial question ?

Sounds like you are intentionally side tracking to me which increases my suspicions .
 
My first ever job was selling domestic and commercial electrical components such as plugs sockets , wiring , swa , RCB's etc . I have never sold a component that could reverse electrical current direction . I am not a novice on components so would like to know how AC suppose to work when there is no apparent component for the process . I could go and read up more on this subject but no doubt it will be written in a confusing way so the average person can't understand it . Here I am looking for an explanation from the horses mouth as they say , surely all these posters so far , somebody can explain the process to me in simple terms to remove my concerns . The more people ignore this , the more I think my suspicions are correct .
Rectifiers.
A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction.
Rectifier

If you live in Britain and have worked with electrical components, you must have heard of Maplin?
Here’s a picture of rectifiers at Maplin
Rectifiers - Copy.jpg
 
''Alternating current (AC) is an electrical current that periodically reverses its direction and changes its magnitude continuously over time.''

I am not electrician but wouldn't that go bang when the direction changes because of the incoming electricity flow ?
I'm not an electrician either, but the fact that things don't go "bang" tells me that you must not understand OR you are trolling. If you really wanted to understand, there are many good websites to explain it to you. Since you seem unwilling to read those, then you must be trolling.
 
touch two live wires together and it will spark , even at low voltage . High voltage would create a bigger spark , a ''bang''

It's not like matter and anti-matter colliding. And the two cycles of AC obviously do not co-exist at the same time in the wire or general loop from the power plant to the household to the ground back to the company generating facility. In the household the UK coded colors for the "hot" wire and the neutral wire you referred to constitute a section of that giant loop. They're the same "line" (with a resistant, power-consuming load in between) when considering the overall circuit they constitute. Not rival enemies or gosh knows what conception is responsible for such confusion.
_
 
Last edited:
I am not electrician but wouldn't that go bang when the direction changes because of the incoming electricity flow ?
No. Electricity is not like water. If you cut a wire the electricity doesn't "spill out."

A simple light bulb , 1.5mm twin and earth , the earth is not attached to the bulb . There is a blue wire and a brown wire . The brown wire is live and the blue is neutral , if the electricity reversed direction , shouldn't the neutral also be a live wire ?

No. The hot goes from -160 to +160, at least here in the US. In your part of the world it's probably closer to +350 to -350. The neutral is not AT ground, but it's close to ground, and should never be more than a few volts away from ground.

If the electricity reversed direction , how does the light bulb not go bang when there is the brown and blue wire pumping current into it ?

If you reversed both - and made them both either ground potential OR hot - the bulb would simply turn off. In fact that's how three-way switches in houses work. They send hot to both sides. No potential difference in that case, so no current flow.

What in a main fuse board allows the electricity to be reversed ? How can a switch work , designed for a circuit , if there is a reverse ?

Switches don't care about which direction current is flowing. They just stop it from flowing.

I think the blue wire goes back into the national grid , I think we are all being ripped off unless I get an answer proving me wrong .

How are you being 'ripped off?' Since all current has to flow in a loop, do you object to the national grid "getting their current back?" If you believe this, try cutting the neutral and grounds off at your fuse box/breaker panel and see what happens. See if your bill goes down, and see what else happens. Use appropriately rated electrical gloves and tools though, so you don't die while trying it.

My first ever job was selling domestic and commercial electrical components such as plugs sockets , wiring , swa , RCB's etc

I think it's great that special needs people can get jobs doing things like that!

I have never sold a component that could reverse electrical current direction .

Yes, you did. You just didn't know it at the time. Three-way switches do just that, but you need two of them. You can even buy reversing switches specifically for motors that is a single switch that reverses the phase to the motor, to get it to spin backwards.

I am not a novice on components

You are very much a novice on components if you don't understand anything about how they work.

so would like to know how AC suppose to work when there is no apparent component for the process . I could go and read up more on this subject but no doubt it will be written in a confusing way so the average person can't understand it .

The average person can understand it, but I can see why you are having trouble.

touch two live wires together and it will spark , even at low voltage . High voltage would create a bigger spark , a ''bang''

Not at all.

Touch two wires together, both at +600VDC, and they will not show the slighest spark. There is no potential difference, so no current will flow. The only time you will get a spark is when there is a potential difference.

Sounds like you are intentionally side tracking to me which increases my suspicions.

And what would those suspicions be?

Is it that there's a worldwide conspiracy to mislead you on how electricity works? Odds of that are pretty low. No one out there really cares what you think about electricity.

Is it that you perhaps don't know much about how things work? That would be an accurate suspicion, due to your aversion to learning about how the world works.
 
Last edited:
And what would those suspicions be?

Is it that there's a worldwide conspiracy to mislead you on how electricity works? Odds of that are pretty low. No one out there really cares what you think about electricity.

Is it that you perhaps don't know much about how things work? That would be an accurate suspicion, due to your aversion to learning about how the world works.
Finally a few answers that I can now ponder over and perhaps research into a bit more .

My suspicions are that the electricity enters my house through a 1 way meter then the excess electricity after use, leaves my house back into the national grid . I suspect I am using perhaps a 10th of what they actually charge for . Alternative current actually being alternative currency for the rulers of the world and that is why they destroyed Tesla after stealing his stuff .
I don't know how AC works , that is a fact and why I am discussing this . I know how the world works and most of it is a con so why not electricity being a part of that .
 
Rectifiers.

Rectifier

If you live in Britain and have worked with electrical components, you must have heard of Maplin?
Here’s a picture of rectifiers at Maplin
View attachment 7794
Just looking at my electricity box in search of a rectifier . I don't seem to see one although there a few bits under plastic covers . Maybe there is one but when I worked in selling these components I don't recall a rectifier .
 
Google Ai says :

  • The live wire carries the alternating voltage to your appliance.
  • The neutral wire completes the circuit, carrying the current back.

This makes zero sense to me , how does it then switch and travel back down the neutral wire ?

Is there a flow tester I can buy to test this ?

The neutral wire carries the current back , where too ? As I said the national grid , it must be .
 
This makes zero sense to me , how does it then switch and travel back down the neutral wire ?
You're confusing current and voltage. A live wire has alternating voltage (like 120) that changes polarity back and forth. The neutral wire stays grounded near 0V. Electrons don't have a net flow like water rushing in a stream, with AC they just oscillate back and forth as polarity changes - it's the EM field which propagates along the area around the wire.

Think of the physical wire and the electrons inside as a guide or channel that shapes and supports the electromagnetic field. Electrons in the huge cables emerging from the power plant don't literally flow over to your house. Hope this helps.
 
My suspicions are that the electricity enters my house through a 1 way meter then the excess electricity after use, leaves my house back into the national grid . I suspect I am using perhaps a 10th of what they actually charge for.
Then do the experiment as I told you to do. For an easier test, cut off the neutral and ground plugs on an appliance. Plug it back in. See if it uses less power.

Use gloves.

Alternative current actually being alternative currency for the rulers of the world and that is why they destroyed Tesla after stealing his stuff .

Tesla was a proponent of AC. You are thinking of Edison, who pushed DC.

I know how the world works

Clearly you don't. You have admitted that books about how the world works are too confusing for you to read. Not being able to read books will be a hindrance to you understanding things.

Just looking at my electricity box in search of a rectifier .

There are no rectifiers in an average breaker panel. They convert AC to DC, and your appliances need AC.

There are, however, rectifiers in most of your appliances.

This makes zero sense to me , how does it then switch and travel back down the neutral wire ?

All current travels in a loop. It has to.

Is there a flow tester I can buy to test this ?

Sure. Buy any power meter; they sell them at hardware stores. You plug it in then plug your appliance into it.


Or get a clamp meter. These work on individual wires. (The wires CANNOT be bundled together or you will read zero.)


The neutral wire carries the current back , where too ? As I said the national grid , it must be .

Yes. That's how electricity works.
 
Yes. That's how electricity works.
As my earlier reply pointed towards, I think he's got a confusion on what current flow consists of, so he was imagining that the neutral wire would become the hotwire and then switch back to neutral 60 x a second. I've met a fair number who don't understand that switching polarity, that ol' sinusoidal swing of voltage, doesn't change what the hot wire and neutral wire do. The neutral wire is still grounded, no matter how the current cycles. Several points he could consider:


Electricity flows because there is a voltage difference (potential) between two points, not just because a wire carries (or guides, really ) current.

So the hot wire oscillates: In a standard 120V household circuit, the hot wire's voltage swings sinusoidally from roughly +170V to -170V (which averages out to 120V RMS) relative to the earth. It changes polarity 120 times per second (in a 60 Hz system, completing 60 full cycles).

Back to my key point: The neutral wire is connected directly to the ground rod/system at your home's service entrance (I've installed a ground rod myself, so I know this happens). Because this neutral is pinned to earth potential (0 volts), it stays near zero volts regardless of which way the current is flowing through the circuit.

So the voltage difference remains on average the same as one goes from the hot wire, through the load (say, a lightbulb) and to neutral.
 
Back
Top